UHBX-WP-P2

HDMI over UTP Extender with HDBaseT™ and PoH ( Wall Plate Sender + Receiver )

  • Extends HDMI or DVI video to 500 ft on just one Cat6
  • Supports virtually all HDMI and DVI resolutions including 4Kx2K
  • Only one end requires power, other side is powered via UTP
  • Power-over-HDBaseT™ meets IEEE 802.3af standard
  • Sturdy metal enclosures with mounting provisions
  • Complies fully with HDBaseT™ standard
    • Share

    Description

    UHBX-WP-P2 is an extender kit ( combination of UHBX-S-WP + UHBX-R-PSE ) from Hall Research that utilizes HDBaseT™ technology. It can send HDMI and PoH (Power-over-HDBaseT™) to 500 ft (150 m) on a single Cat6 cable. The extender uses only one +5v power supply, internally creates 48v PoH and complies with IEEE 802.3af handshake. The P2 extender’s receiver unit provides power to the sender. In standard mode the UHBX-WP-P2 supports DVI and HDMI signals of virtually any resolution up to 4K x 2K to 330 ft (100m), and in Long Reach mode it supports resolutions to 1920×1080 to 500 ft (150 m). The devices are housed in compact and sturdy metal enclosures and have convenient mounting provisions. They are designed and manufactured in the USA.
    The end identified as PSE (power sourcing equipment) injects power on to the Cat6 cable and the side identified as WP (Wall Plate) is powered through the Cat6 cable. The PSE side requires connection of an AC adapter that supplies 5v DC, while the PD side is simply powered through the RJ45 connector from the opposite side.

    Two user selectable distance modes are available: Standard(default) and Long Reach. If the length of UTP cable is less than 100 meters (330 ft), then STD mode should be used. For the lengths above 330 ft Long Reach (L.R.) mode must be set. Long Reach setting can extend maximum of 1080p@60 Hz, 8-bit color (does not support deep-color or 4Kx2K) Power up to 500ft (150m).

    For best results we recommend using Alliance approved cables listed at this site.

    For more information about our other HDBaseT™ products please follow the link below to the Product Selection Chart.

    Features

    • Extends HDMI or DVI video to 500 ft on just one Cat6
    • Supports virtually all HDMI and DVI resolutions including 4Kx2K
    • Only one end requires power, other side is powered via UTP
    • Power-over-HDBaseT™ meets IEEE 802.3af standard
    • Sturdy metal enclosures with mounting provisions
    • Complies fully with HDBaseT™ standard
    • Runs from just one +5vDC supply
    • Fully isolates ground between TX and RX sides
    • Compact, Rugged, Reliable, and Economical
    • Made in USA

    Block Diagram

    Specifications

    Max DistanceStandard Mode (STD): 330 ft (100m)
    Long Reach Mode (LR) : 500 ft (150m)
    Video StandardsDVI (single link) and HDMI (compliant with HDMI 1.4 video specifications including 12 bit color depth, 3D video and 4K support)
    Signal TypeTMDS
    ConnectorsLocking HDMI
    Video ResolutionsDVI: VGA (640x480) to WUXGA (1920x1200)
    HDTV: 480i to 1080p
    Digital Cinema: 4K (4096x2160)
    Supports 4K@60 Hz (4:2:0 8 bit color) or 4K@30 Hz (4:4:4 and 8 bit color)
    Audio FormatsAll HDMI Embedded Audio including: LPCM 7.1CH, Dolby TrueHD and DTS-HD Master Audio (32-192kHz sample rate)
    DDCPass-Thru DDC for reading EDID directly from remotely connected LCD and HDCP handshake
    CECPass-Thru DDC for Consumer Electronics Control compatible devices
    PoHPower-over-HDBaseT™ meets IEEE 802.3af standard. PD side identifies as Class 2 (3.84–6.49 watts). Actual power consumption of PD side is 5.5 watts max
    Power Supply100 VAC to 240 VAC, 50-60 Hz, external; 5 VDC, 3.2 A, regulated
    Actual DC current (powering both –PSE and –PD sides) 1.8A max
    PowerSender: 3.5 watts (12 BTU) maximum
    Receiver: 5.5 watts (19 BTU) maximum
    Temp/humidityStorage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, non-condensing
    Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, non-condensing
    CoolingConvection
    MountingEnd plates have L bracket with hole for surface mounting
    EnclosureMetal (Steel ends and Aluminum extrusion)
    Dimensions1.18" H x 4.13" W x 4.57" D (30mm H x 105mm W x 116mm D) Depth excludes connectors
    Product weightSender: 9.3 oz (0.58 lb or 264 g)
    Receiver: 10 oz (0.63 lb or 284 g)
    Kit (shipping) 37 oz (2.3 lb or 1050 g) includes: sender, receiver, power supply, power cord, HDMI cable, manual, and packaging
    VibrationISTA 1A in carton (International Safe Transit Association)
    SafetyCE
    EMI/EMCCE, FCC Class A
    MTBF90,000 hours (Calculated Estimate)
    Warranty2 years parts and labor

    Downloads

    ManualsDated
    UHBX-WP-P2 Manual
    JUNE 24, 2020
    Spec SheetsDated
    UHBX-WP-P2 Spec Sheet
    JUNE 24, 2020

    Copyright 2020 Hall Research